| sure that the word "TOP" printed on the installation sleeve is facing up). | 
|---|
 | inside the installation sleeve (Important - install onto the two metal pins, making | 
|---|
 | 4. Install the new gaskets and diaphragm onto the carburettor while still contained | 
|---|
 | set the lever height is below the word "Spiral". | 
|---|
 | adjustment point on the brass gauge is on the bottom, the indentation you need to | 
|---|
 | part number OMK500-528 which is included in this spiral diaphragm kit. The | 
|---|
 | 3. Reset the metering lever height using the updated version of the brass "W" gauge | 
|---|
 | metering lever pin. | 
|---|
 | 2. Remove the metering lever and replace with the new one supplied, reusing the old | 
|---|
 | 1. Remove metering cover, old diaphragm and gasket. | 
|---|
 | old metering lever pin. | 
|---|
| Note: | Fitting instructions - | 
|---|
 | it. The metering lever must be replaced with the new one supplied, please reuse the | 
|---|
 | stainless steel spiral is more forgiving but care is still required when handling | 
|---|
 | handle - DO NOT bend or crease the membrane when handling or during assembly! The | 
|---|
| Standard Pack Quantity: | 1 | 
|---|
| Please Note: | Warning - These parts are extremely durable inside the carburettor but fragile to | 
|---|
 | to make assembly quicker and easier (refer to notes below). | 
|---|
 | use the new spiral diaphragm kits. | 
|---|
 | All parts (except the metering lever) are contained in a clever installation sleeve | 
|---|
 | Currently over 500 Walbro diaphragm carburettor model numbers can be upgraded to | 
|---|
 | modern fuels. | 
|---|
 | diaphragm - impervious to the effects of Ethanol and other additives found in | 
|---|
| Features: | A membrane with a high grade teflon film in the centre and a stainless steel spiral | 
|---|
 | WTF-10, WTF-11 and WTF-12. Please refer to the notes below. | 
|---|
 | WTE-17, WTE-18, WTE-20, WTE-22, WTEA-1, WTEA-11, WTF-1, WTF-2, WTF-5, WTF-6, WTF-7, | 
|---|
 | to WTE-2, WTE-3, WTE-4, WTE-7, WTE-8, WTE-9, WTE-12, WTE-14, WTE-15, WTE-16, | 
|---|
 | suitable for use with selected Walbro carburettor models including but not limited | 
|---|
| Fits: | This genuine Walbro K4-WYTA spiral metering diaphragm and gasket upgrade kit is | 
|---|
| Replaces OEM: | Walbro K4-WYTA | 
|---|
 | deteriorate with age. | 
|---|
 | impervious to the effects of Ethanol and additives in modern fuels and does not | 
|---|
 | compliant spiral metering diaphragm. The new spiral metering diaphragm is | 
|---|
 | carburettor from the traditional rubber metering diaphragm to Walbro's ethanol | 
|---|
| Editorial: | Walbro's patented spiral metering diaphragm upgrade kit allows you to convert your | 
|---|
 | Gauge | 
|---|
| Description: | Genuine Walbro K4-WYTA Spiral Metering Diaphragm Upgrade Kit - Includes Brass "W" | 
|---|
 | 5. Hold the installation sleeve with one hand and put the metering cover on over | 
|---|
 | the top to hold it down. | 
|---|
 | 6. Install the four screws and start them by just one turn each. | 
|---|
 | 7. Then remove the clip off the end and pull the installation sleeve out, then | 
|---|
 | torque the screws down normally. | 
|---|
| Footnote: | When comparing this fitment application information to your carburettor model | 
|---|
 | please disregard all letters (A, B, C) and -1 that may be at the end of your | 
|---|
 | carburetor model number. | 
|---|
| Brand: | Genuine Walbro, | 
|---|
| Product Line: | Diaphragm and Gasket Set, Gasket and Diaphragm Set, Metering Diaphragm and Gasket | 
|---|
 | kit - Spiral, Spiral Metering Diaphragm and Gasket Set, | 
|---|
| Description: | Genuine Walbro K4-WYTA Spiral Metering Diaphragm Upgrade Kit - Includes Brass "W" | 
|---|
 | Gauge | 
|---|
| Editorial: | Walbro's patented spiral metering diaphragm upgrade kit allows you to convert your | 
|---|
 | carburettor from the traditional rubber metering diaphragm to Walbro's ethanol | 
|---|
 | compliant spiral metering diaphragm. The new spiral metering diaphragm is | 
|---|
 | impervious to the effects of Ethanol and additives in modern fuels and does not | 
|---|
 | deteriorate with age. | 
|---|
| Replaces OEM: | Walbro K4-WYTA | 
|---|
| Fits: | This genuine Walbro K4-WYTA spiral metering diaphragm and gasket upgrade kit is | 
|---|
 | suitable for use with selected Walbro carburettor models including but not limited | 
|---|
 | to WTE-2, WTE-3, WTE-4, WTE-7, WTE-8, WTE-9, WTE-12, WTE-14, WTE-15, WTE-16, | 
|---|
 | WTE-17, WTE-18, WTE-20, WTE-22, WTEA-1, WTEA-11, WTF-1, WTF-2, WTF-5, WTF-6, WTF-7, | 
|---|
 | WTF-10, WTF-11 and WTF-12. Please refer to the notes below. | 
|---|
| Features: | A membrane with a high grade teflon film in the centre and a stainless steel spiral | 
|---|
 | diaphragm - impervious to the effects of Ethanol and other additives found in | 
|---|
 | modern fuels. | 
|---|
 | Currently over 500 Walbro diaphragm carburettor model numbers can be upgraded to | 
|---|
 | use the new spiral diaphragm kits. | 
|---|
 | All parts (except the metering lever) are contained in a clever installation sleeve | 
|---|
 | to make assembly quicker and easier (refer to notes below). | 
|---|
| Standard Pack Quantity: | 1 | 
|---|
| Please Note: | Warning - These parts are extremely durable inside the carburettor but fragile to | 
|---|
 | handle - DO NOT bend or crease the membrane when handling or during assembly! The | 
|---|
 | stainless steel spiral is more forgiving but care is still required when handling | 
|---|
 | it. The metering lever must be replaced with the new one supplied, please reuse the | 
|---|
 | old metering lever pin. | 
|---|
| Note: | Fitting instructions - | 
|---|
 | 1. Remove metering cover, old diaphragm and gasket. | 
|---|
 | 2. Remove the metering lever and replace with the new one supplied, reusing the old | 
|---|
 | metering lever pin. | 
|---|
 | 3. Reset the metering lever height using the updated version of the brass "W" gauge | 
|---|
 | part number OMK500-528 which is included in this spiral diaphragm kit. The | 
|---|
 | adjustment point on the brass gauge is on the bottom, the indentation you need to | 
|---|
 | set the lever height is below the word "Spiral". | 
|---|
 | 4. Install the new gaskets and diaphragm onto the carburettor while still contained | 
|---|
 | inside the installation sleeve (Important - install onto the two metal pins, making | 
|---|
 | sure that the word "TOP" printed on the installation sleeve is facing up). | 
|---|
 | 5. Hold the installation sleeve with one hand and put the metering cover on over | 
|---|
 | the top to hold it down. | 
|---|
 | 6. Install the four screws and start them by just one turn each. | 
|---|
 | 7. Then remove the clip off the end and pull the installation sleeve out, then | 
|---|
 | torque the screws down normally. | 
|---|
| Footnote: | When comparing this fitment application information to your carburettor model | 
|---|
 | please disregard all letters (A, B, C) and -1 that may be at the end of your | 
|---|
 | carburetor model number. | 
|---|
| Brand: | Genuine Walbro, | 
|---|
| Product Line: | Diaphragm and Gasket Set, Gasket and Diaphragm Set, Metering Diaphragm and Gasket | 
|---|
 | kit - Spiral, Spiral Metering Diaphragm and Gasket Set, | 
|---|
| Description: | Genuine Walbro K4-WYTA Spiral Metering Diaphragm Upgrade Kit - Includes Brass "W" | 
|---|
 | Gauge | 
|---|
| Editorial: | Walbro's patented spiral metering diaphragm upgrade kit allows you to convert your | 
|---|
 | carburettor from the traditional rubber metering diaphragm to Walbro's ethanol | 
|---|
 | compliant spiral metering diaphragm. The new spiral metering diaphragm is | 
|---|
 | impervious to the effects of Ethanol and additives in modern fuels and does not | 
|---|
 | deteriorate with age. | 
|---|
| Replaces OEM: | Walbro K4-WYTA | 
|---|
| Fits: | This genuine Walbro K4-WYTA spiral metering diaphragm and gasket upgrade kit is | 
|---|
 | suitable for use with selected Walbro carburettor models including but not limited | 
|---|
 | to WTE-2, WTE-3, WTE-4, WTE-7, WTE-8, WTE-9, WTE-12, WTE-14, WTE-15, WTE-16, | 
|---|
 | WTE-17, WTE-18, WTE-20, WTE-22, WTEA-1, WTEA-11, WTF-1, WTF-2, WTF-5, WTF-6, WTF-7, | 
|---|
 | WTF-10, WTF-11 and WTF-12. Please refer to the notes below. | 
|---|
| Features: | A membrane with a high grade teflon film in the centre and a stainless steel spiral | 
|---|
 | diaphragm - impervious to the effects of Ethanol and other additives found in | 
|---|
 | modern fuels. | 
|---|
 | Currently over 500 Walbro diaphragm carburettor model numbers can be upgraded to | 
|---|
 | use the new spiral diaphragm kits. | 
|---|
 | All parts (except the metering lever) are contained in a clever installation sleeve | 
|---|
 | to make assembly quicker and easier (refer to notes below). | 
|---|
| Standard Pack Quantity: | 1 | 
|---|
| Please Note: | Warning - These parts are extremely durable inside the carburettor but fragile to | 
|---|
 | handle - DO NOT bend or crease the membrane when handling or during assembly! The | 
|---|
 | stainless steel spiral is more forgiving but care is still required when handling | 
|---|
 | it. The metering lever must be replaced with the new one supplied, please reuse the | 
|---|
 | old metering lever pin. | 
|---|
| Note: | Fitting instructions - | 
|---|
 | 1. Remove metering cover, old diaphragm and gasket. | 
|---|
 | 2. Remove the metering lever and replace with the new one supplied, reusing the old | 
|---|
 | metering lever pin. | 
|---|
 | 3. Reset the metering lever height using the updated version of the brass "W" gauge | 
|---|
 | part number OMK500-528 which is included in this spiral diaphragm kit. The | 
|---|
 | adjustment point on the brass gauge is on the bottom, the indentation you need to | 
|---|
 | set the lever height is below the word "Spiral". | 
|---|
 | 4. Install the new gaskets and diaphragm onto the carburettor while still contained | 
|---|
 | inside the installation sleeve (Important - install onto the two metal pins, making | 
|---|
 | sure that the word "TOP" printed on the installation sleeve is facing up). | 
|---|
 | 5. Hold the installation sleeve with one hand and put the metering cover on over | 
|---|
 | the top to hold it down. | 
|---|
 | 6. Install the four screws and start them by just one turn each. | 
|---|
 | 7. Then remove the clip off the end and pull the installation sleeve out, then | 
|---|
 | torque the screws down normally. | 
|---|
| Footnote: | When comparing this fitment application information to your carburettor model | 
|---|
 | please disregard all letters (A, B, C) and -1 that may be at the end of your | 
|---|
 | carburetor model number. | 
|---|
| Brand: | Genuine Walbro, | 
|---|
| Product Line: | Diaphragm and Gasket Set, Gasket and Diaphragm Set, Metering Diaphragm and Gasket | 
|---|
 | kit - Spiral, Spiral Metering Diaphragm and Gasket Set, | 
|---|
| Description: | Genuine Walbro K4-WYTA Spiral Metering Diaphragm Upgrade Kit - Includes Brass "W" | 
|---|
 | Gauge | 
|---|
| Editorial: | Walbro's patented spiral metering diaphragm upgrade kit allows you to convert your | 
|---|
 | carburettor from the traditional rubber metering diaphragm to Walbro's ethanol | 
|---|
 | compliant spiral metering diaphragm. The new spiral metering diaphragm is | 
|---|
 | impervious to the effects of Ethanol and additives in modern fuels and does not | 
|---|
 | deteriorate with age. | 
|---|
| Replaces OEM: | Walbro K4-WYTA | 
|---|
| Fits: | This genuine Walbro K4-WYTA spiral metering diaphragm and gasket upgrade kit is | 
|---|
 | suitable for use with selected Walbro carburettor models including but not limited | 
|---|
 | to WTE-2, WTE-3, WTE-4, WTE-7, WTE-8, WTE-9, WTE-12, WTE-14, WTE-15, WTE-16, | 
|---|
 | WTE-17, WTE-18, WTE-20, WTE-22, WTEA-1, WTEA-11, WTF-1, WTF-2, WTF-5, WTF-6, WTF-7, | 
|---|
 | WTF-10, WTF-11 and WTF-12. Please refer to the notes below. | 
|---|
| Features: | A membrane with a high grade teflon film in the centre and a stainless steel spiral | 
|---|
 | diaphragm - impervious to the effects of Ethanol and other additives found in | 
|---|
 | modern fuels. | 
|---|
 | Currently over 500 Walbro diaphragm carburettor model numbers can be upgraded to | 
|---|
 | use the new spiral diaphragm kits. | 
|---|
 | All parts (except the metering lever) are contained in a clever installation sleeve | 
|---|
 | to make assembly quicker and easier (refer to notes below). | 
|---|
| Standard Pack Quantity: | 1 | 
|---|
| Please Note: | Warning - These parts are extremely durable inside the carburettor but fragile to | 
|---|
 | handle - DO NOT bend or crease the membrane when handling or during assembly! The | 
|---|
 | stainless steel spiral is more forgiving but care is still required when handling | 
|---|
 | it. The metering lever must be replaced with the new one supplied, please reuse the | 
|---|
 | old metering lever pin. | 
|---|
| Note: | Fitting instructions - | 
|---|
 | 1. Remove metering cover, old diaphragm and gasket. | 
|---|
 | 2. Remove the metering lever and replace with the new one supplied, reusing the old | 
|---|
 | metering lever pin. | 
|---|
 | 3. Reset the metering lever height using the updated version of the brass "W" gauge | 
|---|
 | part number OMK500-528 which is included in this spiral diaphragm kit. The | 
|---|
 | adjustment point on the brass gauge is on the bottom, the indentation you need to | 
|---|
 | set the lever height is below the word "Spiral". | 
|---|
 | 4. Install the new gaskets and diaphragm onto the carburettor while still contained | 
|---|
 | inside the installation sleeve (Important - install onto the two metal pins, making | 
|---|
 | sure that the word "TOP" printed on the installation sleeve is facing up). | 
|---|
 | 5. Hold the installation sleeve with one hand and put the metering cover on over | 
|---|
 | the top to hold it down. | 
|---|
 | 6. Install the four screws and start them by just one turn each. | 
|---|
 | 7. Then remove the clip off the end and pull the installation sleeve out, then | 
|---|
 | torque the screws down normally. | 
|---|
| Footnote: | When comparing this fitment application information to your carburettor model | 
|---|
 | please disregard all letters (A, B, C) and -1 that may be at the end of your | 
|---|
 | carburetor model number. | 
|---|
| Brand: | Genuine Walbro, | 
|---|
| Product Line: | Diaphragm and Gasket Set, Gasket and Diaphragm Set, Metering Diaphragm and Gasket | 
|---|
 | kit - Spiral, Spiral Metering Diaphragm and Gasket Set, | 
|---|
| Description: | Genuine Walbro K4-WYTA Spiral Metering Diaphragm Upgrade Kit - Includes Brass "W" | 
|---|
 | Gauge | 
|---|
| Editorial: | Walbro's patented spiral metering diaphragm upgrade kit allows you to convert your | 
|---|
 | carburettor from the traditional rubber metering diaphragm to Walbro's ethanol | 
|---|
 | compliant spiral metering diaphragm. The new spiral metering diaphragm is | 
|---|
 | impervious to the effects of Ethanol and additives in modern fuels and does not | 
|---|
 | deteriorate with age. | 
|---|
| Replaces OEM: | Walbro K4-WYTA | 
|---|
| Fits: | This genuine Walbro K4-WYTA spiral metering diaphragm and gasket upgrade kit is | 
|---|
 | suitable for use with selected Walbro carburettor models including but not limited | 
|---|
 | to WTE-2, WTE-3, WTE-4, WTE-7, WTE-8, WTE-9, WTE-12, WTE-14, WTE-15, WTE-16, | 
|---|
 | WTE-17, WTE-18, WTE-20, WTE-22, WTEA-1, WTEA-11, WTF-1, WTF-2, WTF-5, WTF-6, WTF-7, | 
|---|
 | WTF-10, WTF-11 and WTF-12. Please refer to the notes below. | 
|---|
| Features: | A membrane with a high grade teflon film in the centre and a stainless steel spiral | 
|---|
 | diaphragm - impervious to the effects of Ethanol and other additives found in | 
|---|
 | modern fuels. | 
|---|
 | Currently over 500 Walbro diaphragm carburettor model numbers can be upgraded to | 
|---|
 | use the new spiral diaphragm kits. | 
|---|
 | All parts (except the metering lever) are contained in a clever installation sleeve | 
|---|
 | to make assembly quicker and easier (refer to notes below). | 
|---|
| Standard Pack Quantity: | 1 | 
|---|
| Please Note: | Warning - These parts are extremely durable inside the carburettor but fragile to | 
|---|
 | handle - DO NOT bend or crease the membrane when handling or during assembly! The | 
|---|
 | stainless steel spiral is more forgiving but care is still required when handling | 
|---|
 | it. The metering lever must be replaced with the new one supplied, please reuse the | 
|---|
 | old metering lever pin. | 
|---|
| Note: | Fitting instructions - | 
|---|
 | 1. Remove metering cover, old diaphragm and gasket. | 
|---|
 | 2. Remove the metering lever and replace with the new one supplied, reusing the old | 
|---|
 | metering lever pin. | 
|---|
 | 3. Reset the metering lever height using the updated version of the brass "W" gauge | 
|---|
 | part number OMK500-528 which is included in this spiral diaphragm kit. The | 
|---|
 | adjustment point on the brass gauge is on the bottom, the indentation you need to | 
|---|
 | set the lever height is below the word "Spiral". | 
|---|
 | 4. Install the new gaskets and diaphragm onto the carburettor while still contained | 
|---|
 | inside the installation sleeve (Important - install onto the two metal pins, making | 
|---|
 | sure that the word "TOP" printed on the installation sleeve is facing up). | 
|---|
 | 5. Hold the installation sleeve with one hand and put the metering cover on over | 
|---|
 | the top to hold it down. | 
|---|
 | 6. Install the four screws and start them by just one turn each. | 
|---|
 | 7. Then remove the clip off the end and pull the installation sleeve out, then | 
|---|
 | torque the screws down normally. | 
|---|
| Footnote: | When comparing this fitment application information to your carburettor model | 
|---|
 | please disregard all letters (A, B, C) and -1 that may be at the end of your | 
|---|
 | carburetor model number. | 
|---|
| Brand: | Genuine Walbro, | 
|---|
| Product Line: | Diaphragm and Gasket Set, Gasket and Diaphragm Set, Metering Diaphragm and Gasket | 
|---|
 | kit - Spiral, Spiral Metering Diaphragm and Gasket Set, | 
|---|